laplander nu list (17)
bulkheads were fitted to mount cupboards and other things
|
laplander nu list (20)
a fold down bed that doubles as a seat
|
laplander nu list (88)
two 20watt inverters for refrigerator and other items
|
laplander nu list (6)
took sump pan off to clean service oil pump, it now gives
Date: 8/14/2009
Views: 11
|
laplander nu list (105)
fit new distributor, water pump, and thermostat
Date: 2/26/2009
Views: 15
|
laplander nu list (82)
stripped engine head for decoke and to regrind valves it had poor compression
Date: 8/11/2009
Views: 16
|
b18 cylinder head 003 (800x600)
after decoke
Date: 8/11/2009
Views: 11
|
b18 cylinder head 004 (800x600)
head cleaned and valves springs and oil seals checked
Date: 8/11/2009
Views: 14
|
laplander nu list (83)
cleaned cylinder bores and piston heads
Date: 8/11/2009
Views: 13
|
laplander nu list (1)
regimental plate and military registration # plate made
|
17 (800x600)
finished worktop , includes cooker, sink, fridge, drawer for cooking items,50 litres of water and gas bottle
|
19 (800x600)
blinds fasten down with velcro
|
jerrycan box 001 (800x600)
spare fuel storage restored and ready to put back
|
laplander nu list (74)
photos for insurance valuer # 1
|
laplander nu list (75)
photo # 2
|
laplander nu list (76)
photo # 3
|
laplander nu list (77)
photo # 4
|
free wheeling hub (800x600)
free wheeling hubs fitted
|
headlamp upgrade 003 (800x600)
started with two live feeds for the relays, these have 45 amp fuzes in at the moment
|
headlamp upgrade 006 (800x600)
fuze holders can be closed for protection of shorting
|
headlamp upgrade 002 (800x600)
i encased the cables in a protective conduit, which is routed a discreet and short distance to the dash
|
headlamp upgrade 011 (800x600)
the two live cables feed each relay which is in turn earthed close to the valp fuze links. two feeds from the relays are paired in a plastic box and routed to the headlamps. the trigger for the relays are connected to the relevant points in the valp fuze
|
headlamp upgrade 001 (800x600)
everything tidied up and a bit of rust taken care of,only 3 eight mm holes drill and protected with rubber grommets.
|
headlamp upgrade 007 (800x600)
headlamp with new 10 mm cable and earths. i have left the original cable in place throughout the project so that the valps wiring can be put back to normal headlamps and the relays used on two extra off road lamps of high power.
|
Recent comments
valp restoration/headlamp upgrade.
show full show summaryi fit 2 x h/4 quartz halogen bulbs which were 65 watts, which were better than the valps original glow worm bulbs but then i acquired some 130/90 eye ball burners. i guess the cables on the valp may have taken the extra load but the light switches...
i fit 2 x h/4 quartz halogen bulbs which were 65 watts, which were better than the valps original glow worm bulbs but then i acquired some 130/90 eye ball burners. i guess the cables on the valp may have taken the extra load but the light switches certainly would have burnt out in a very short time. so now i am satisfied with the project which took about two days of rolling about under the valp and trying different routes for the cables.
Posted by Dave Boston-dunn on 01/24/10 13:05:17